2009年11月24日星期二

Shares of global lithium supply by country

Most think there is enough lithium for hybrid boom

Don’t care about lithium supplies demanded to make the batteries for all those hybrids and electric vehicles on the way. Hp laptop battery There are dozens of the stuff–at least for the next decade. On the far side that, though, opinions differ.


The supply of lithium has been a topic of debate since automakers beginning adjust their sights on lithium ion batteries. Those batteries are seen as the key to making a practical electric car because they are lighter and more powerful than the nickel-metal hydride batteries used in today’s hybrids.


They’re still costly. And because the lithium ion batteries remain an emerging technology, questions linger about their life span, durability, and safety. But for now, lithium ion batteries remain the most likely energy source for electric vehicles.


Locating lithium


Shares of global lithium supply by country

General Motors Co., Toyota Motor Corp., Mitsubishi Motors Corp., Nissan Motor Co. and Daimler AG are among the automakers that plan to launch electric or plug-in hybrid vehicles by 2011. All plan to use lithium ion batteries. All, therefore, closely monitor the supply and price of lithium.


As demand for lithium ion batteries for laptops, cell phones, and now vehicles soared, HP Pavilion ZD7000 Battery, prices of lithium carbonate, a raw material used to produce lithium, raised to $5,500 a ton in 2008 from $2,000 in 2004, says Roskill Information Services, a metals and minerals research consulting firm. The jump came despite rising global output.


As prices climbed, analysts began studying the outlook for lithium. The question: Much as today’s drivers are hostage to scarce, increasingly costly oil, will tomorrow’s drivers be reliant on scarce, increasingly costly lithium?


Some of those studies, along with executives at battery companies, HP CGR-B1870AE Battery,
HP Pavilion ZD7000 Battery, HP PP2182D Battery, HP 338794-001 Battery, say worries about scarcity are overblown. They say the world has plenty of lithium to power electric and plug-in hybrid vehicles, in addition to consumer electronics.


Gerson Lehrman Group, a New York consulting firm, estimates that even if 500,000 cars powered by lithium ion batteries were produced in 2015, they would use less than 10 percent of last year’s global lithium output.


The calculation was based on a report that Nissan’s upcoming Leaf electric vehicle uses about 8.8 pounds of lithium in its battery pack. At the 2008 price cited above, the small amount of lithium needed for each car would come to $24–just a fraction of the total cost of an electric vehicle’s VGP-BPS2C battery, which can run as high as $10,000.


Gerson Lehrman says: HP PP2182D Battery “Oversupply might be a more pressing question than lithium availability.”


Chris Richter, an auto analyst with CLSA Asia-Pacific Markets in Tokyo, puts it another way. “Lithium is one of the more abundant elements in the Earth’s crust,” he says. “Of all the various problems with this technology, running out of lithium is not one of them.”


Neil Maguire, vice president of business development at Imara Corp., a lithium ion Latitude battery startup in Menlo Park, Calif., says supply is sufficient to meet near-term demand.


Beyond that, if the volume of electric vehicles soars so much that lithium supplies become an issue, older lithium ion batteries can be recycled for the raw materials in them, he says.


“We don’t worry about lithium availability,” Maguire says.


Mining companies are racing to boost lithium output and find new sources.


Global lithium production reached 22,800 tons in 2008, up from 13,000 tons in 2000, according to Roskill Information Services.


Adding capacity in China or tapping lithium reserves in new countries could add 10,000 tons of output by the early 2010s, Gerson Lehrman forecasts.

Trouble with lithium


But a 2008 report titled “The Trouble with Lithium 2,” by Meridian International Research, a renewable-energy think tank in France,HP 338794-001 Battery concluded that the world faces a shortage when vehicle demand is added to considerable consumer electronics demand.


“Realistic lithium production increases have no prospect of also meeting the demands of the entire product and propulsion revolution in the global automotive industry in the next decade,” the report said.


Estimates of global reserves vary. Meridian puts it at 4 million tons, far below the 20 million tons cited by some sources. The trick is finding deposits of high-quality lithium that are economically viable to extract.


Car batteries require about 100 times the amount of lithium used in a laptop computer battery, putting a strain on global deposits, says William Tahil, author of the Meridian report.


He concedes that increased lithium production can keep pace with electric-vehicle production in the low millions of units a year. But looking further into the future, Tahil says,HP CGR-B1870AE Battery,
HP Pavilion ZD7000 Battery, HP PP2182D Battery, HP 338794-001 Battery, there is not enough for a wholesale conversion of the entire world’s auto industry from internal-combustion engines to battery-powered electric motors.


“There’s enough for a niche market,” Tahil says, “but nothing close to enough for the mass market.”

digital camera battery

A digital camera battery is probably the most important digital camera accessory. Some digital cameras can consume power at an incredible rate, providing only a few hours of continuous shooting time before the battery is exhausted. Other cameras are famous for the long life of their digital camera battery which allows users to snap away with barely a thought to power consumption. It is important to know how you plan to use your camera and what kind of battery it needs.


There are two types of Digital Camera Battery. Hp laptop battery The most widely available digital camera battery is a standard AA-size battery. The other type is a rechargeable battery that is made by the manufacturer, otherwise known as a proprietary battery.


A proprietary digital camera battery offers the advantage of being lighter and more compact,HP 342661-001 Battery,, HP pavilion dv6000 Battery(hp dv6000 battery)
HP Pavilion dv8000 Battery(hp dv8000 battery), but they are often more expensive, making the prospect of buying one or two backup sets much less appealing.


The alkaline AA-size digital camera battery usually has a very short life - less than an hour in extreme cases - when used in a digital camera. This type of battery makes an acceptable emergency backup, especially if you are travelling with your camera. However, the Nickel Metal Hydride (NiMH) digital camera battery can be used instead of the alkaline ones with a Charger and this rechargeable digital camera battery has a substantially longer life at an affordable price.


Another type of AA-size battery is the non-rechargeable Lithium A1045 batteries and rechargeable Nickel Cadmium (NiCD) batteries. The lithium digital camera battery has a superior life to alkaline AA’s and offers good cold-weather performance but their price and non-rechargeable feature make them less useful than rechargeable NiMH batteries. It is also important to ensure that your camera can take a lithium digital camera battery. On the other hand, the NiCD digital camera battery offers the advantage of retaining their charge while unused, unlike NiMH cells, but have shorter lives and need to be discharged completely before recharging which could be very inconvenient.


The LCD screen of a digital camera is responsible for consuming the most power, HP 342661-001 Battery so it is worth only using the LCD when necessary to help save the battery life. Always try to carry at least one backup set of batteries, especially if you plan on being away from power outlets for an extended period of time. The current alkaline AA-size battery can make a convenient emergency backup if your original digital camera battery fails.

Researchers at the Uppsala University in Sweden have developed a new thin-film battery made from salt and cellulose. This salt and paper battery uses a thin-film which makes it an attractive feature for many portable devices that draw a low current. It can be used in many low-power devices, such as wireless sensors, smart cards, medical implants and RFID tags.


The cellulose is derived from a polluting alga found in lakes and seas. The alga’s walls contain cellulose that has a different nanostructure, which gives it 100 times the surface area. The lightweight, rechargeable battery is made by coating the paper, HP 342661-001 Battery,, HP pavilion dv6000 Battery(hp dv6000 battery)
HP Pavilion dv8000 Battery(hp dv8000 battery), made from this cellulose, with a conducting polymer, and inserting a salt-solution-soaked filter paper between the paper electrodes.


In comparison with a lithium battery that would take 20 minutes to recharge, this new battery can be recharged in tens of seconds because the ions flow through the thin electrode quickly. The salt and paper battery will be made available to distributors in about three years. For the moment it is still in the early stages of development.


The differences between Ni-MH battery and Lithium battery

1, the weight


Each one-voltage battery cells of view are the nickel-metal hydride and nickel-cadmium 1.2V,HP pavilion dv6000 Battery while the lithium battery is in fact only 3.6 V, voltage of the lithium battery is 3 times the other two. And the weight of the same type of lithium battery and nickel-cadmium batteries is almost equal, while heavier than Ni-Ni-MH battery. We can see that the battery itself, the weight of each different, but the top of the lithium battery voltage of 3.6V, as in the case of the output voltage is equal to the number of combinations of a single cell may be reduced after the third is forming the battery weight and size reduction.

2, the memory effect



Nickel-metal hydride batteries and nickel-cadmium batteries have the same memory effect. Therefore, the direction of the regular discharge is necessary. This regular discharge management are at the fuzzy edge was treated, or even some knowledge of improper conduct discharge (discharge or use a number of times each time after discharge were the result of the company vary) This landfill management cumbersome use nickel-hydride VGP-BPS2B batteries, metal can not be avoided. In terms of lithium battery, because of no memory effect, it’s very practical and easy to use. It is completely without regard to the residual voltage is how much can be charged directly, charging time can be shortened by nature.


3, self-discharge rate


Nickel-cadmium batteries discharge 15 ~ 30% (month). Ni-MH battery for 25 ~ 35% (month), a rechargeable Lithium is 2 ~ 5% (month). HP Pavilion dv8000 Battery Than nickel-metal hydride batteries self-discharge rate is highest, while the lithium satelite battery expertise with the other two types of rates of discharge of the battery compared to very low.


4 Price


Nickel-metal hydride batteries and lithium batteries can not be insensible to overload. Therefore, nickel-hydride batteries, metal mode constant current load control PICK CUT when the charging voltage is higher, HP 342661-001 Battery,, HP pavilion dv6000 Battery(hp dv6000 battery)
HP Pavilion dv8000 Battery(hp dv8000 battery), to stop the load as the best means of support. The lithium batteries using a constant current, constant voltage mode, the best, if nickel cadmium battery charger DV-controlled manner, while pairs of nickel-metal hydride batteries and rechargeable lithium batteri




digital camera battery

A digital camera battery is probably the most important digital camera accessory. Some digital cameras can consume power at an incredible rate, providing only a few hours of continuous shooting time before the battery is exhausted. Other cameras are famous for the long life of their digital camera battery which allows users to snap away with barely a thought to power consumption. It is important to know how you plan to use your camera and what kind of battery it needs.


There are two types of Digital Camera Battery. Hp laptop battery The most widely available digital camera battery is a standard AA-size battery. The other type is a rechargeable battery that is made by the manufacturer, otherwise known as a proprietary battery.


A proprietary digital camera battery offers the advantage of being lighter and more compact,HP 342661-001 Battery,, HP pavilion dv6000 Battery(hp dv6000 battery)
HP Pavilion dv8000 Battery(hp dv8000 battery), but they are often more expensive, making the prospect of buying one or two backup sets much less appealing.


The alkaline AA-size digital camera battery usually has a very short life - less than an hour in extreme cases - when used in a digital camera. This type of battery makes an acceptable emergency backup, especially if you are travelling with your camera. However, the Nickel Metal Hydride (NiMH) digital camera battery can be used instead of the alkaline ones with a Charger and this rechargeable digital camera battery has a substantially longer life at an affordable price.


Another type of AA-size battery is the non-rechargeable Lithium A1045 batteries and rechargeable Nickel Cadmium (NiCD) batteries. The lithium digital camera battery has a superior life to alkaline AA’s and offers good cold-weather performance but their price and non-rechargeable feature make them less useful than rechargeable NiMH batteries. It is also important to ensure that your camera can take a lithium digital camera battery. On the other hand, the NiCD digital camera battery offers the advantage of retaining their charge while unused, unlike NiMH cells, but have shorter lives and need to be discharged completely before recharging which could be very inconvenient.


The LCD screen of a digital camera is responsible for consuming the most power, HP 342661-001 Battery so it is worth only using the LCD when necessary to help save the battery life. Always try to carry at least one backup set of batteries, especially if you plan on being away from power outlets for an extended period of time. The current alkaline AA-size battery can make a convenient emergency backup if your original digital camera battery fails.

Researchers at the Uppsala University in Sweden have developed a new thin-film battery made from salt and cellulose. This salt and paper battery uses a thin-film which makes it an attractive feature for many portable devices that draw a low current. It can be used in many low-power devices, such as wireless sensors, smart cards, medical implants and RFID tags.


The cellulose is derived from a polluting alga found in lakes and seas. The alga’s walls contain cellulose that has a different nanostructure, which gives it 100 times the surface area. The lightweight, rechargeable battery is made by coating the paper, HP 342661-001 Battery,, HP pavilion dv6000 Battery(hp dv6000 battery)
HP Pavilion dv8000 Battery(hp dv8000 battery), made from this cellulose, with a conducting polymer, and inserting a salt-solution-soaked filter paper between the paper electrodes.


In comparison with a lithium battery that would take 20 minutes to recharge, this new battery can be recharged in tens of seconds because the ions flow through the thin electrode quickly. The salt and paper battery will be made available to distributors in about three years. For the moment it is still in the early stages of development.


The differences between Ni-MH battery and Lithium battery

1, the weight


Each one-voltage battery cells of view are the nickel-metal hydride and nickel-cadmium 1.2V,HP pavilion dv6000 Battery while the lithium battery is in fact only 3.6 V, voltage of the lithium battery is 3 times the other two. And the weight of the same type of lithium battery and nickel-cadmium batteries is almost equal, while heavier than Ni-Ni-MH battery. We can see that the battery itself, the weight of each different, but the top of the lithium battery voltage of 3.6V, as in the case of the output voltage is equal to the number of combinations of a single cell may be reduced after the third is forming the battery weight and size reduction.

2, the memory effect



Nickel-metal hydride batteries and nickel-cadmium batteries have the same memory effect. Therefore, the direction of the regular discharge is necessary. This regular discharge management are at the fuzzy edge was treated, or even some knowledge of improper conduct discharge (discharge or use a number of times each time after discharge were the result of the company vary) This landfill management cumbersome use nickel-hydride VGP-BPS2B batteries, metal can not be avoided. In terms of lithium battery, because of no memory effect, it’s very practical and easy to use. It is completely without regard to the residual voltage is how much can be charged directly, charging time can be shortened by nature.


3, self-discharge rate


Nickel-cadmium batteries discharge 15 ~ 30% (month). Ni-MH battery for 25 ~ 35% (month), a rechargeable Lithium is 2 ~ 5% (month). HP Pavilion dv8000 Battery Than nickel-metal hydride batteries self-discharge rate is highest, while the lithium satelite battery expertise with the other two types of rates of discharge of the battery compared to very low.


4 Price


Nickel-metal hydride batteries and lithium batteries can not be insensible to overload. Therefore, nickel-hydride batteries, metal mode constant current load control PICK CUT when the charging voltage is higher, HP 342661-001 Battery,, HP pavilion dv6000 Battery(hp dv6000 battery)
HP Pavilion dv8000 Battery(hp dv8000 battery), to stop the load as the best means of support. The lithium batteries using a constant current, constant voltage mode, the best, if nickel cadmium battery charger DV-controlled manner, while pairs of nickel-metal hydride batteries and rechargeable lithium batteri




the most popular laptop battery

Network, the most popular laptop battery BatteryMon2.0 tests software, it is a green laptop battery test software, there is the Chinese version,Hp laptop battery I felt this test software was good, more Intuitive! Users can see the discharge curve of the battery to determine the current state of the battery, but can also test the use of maximum power from your battery time! This article describes a new set of software testing Eate battery is a good software can be downloaded free, interested friends may want to test yourself down under the battery.


Preface test battery for notebook: Laptop battery always undermine the effectiveness of the user to understand laptop battery at the maximum load, minimum load, or other ordinary cases, what happens to last they became the laptop users, the future of mobile computer users concerned about the main factors.


Laptop battery test body: The laptop has some knowledge of friends may know yourself to determine the resistance of the batteries in your laptop in two ways.


Laptop battery Test Method 1: the battery is fully charged unplug the power cord from the outlet, start the motherboard to supervise every moment to write a report file information (e.g., CPU frequency), so that when the battery after the power is empty, HP Pavilion dv9000 Battery(hp dv9000 battery), HP EV087AA Battery, you can see the records of test report start and end time, their difference is the lifetime of the battery. To avoid the process of writing the information because of electricity caused by the report file is damaged, you’d better put in two different file formats along with written information. This method may help you estimate the load at the minimum operating time of battery. If you want to test your computer when you run certain applications, the operating time of battery you can cut the power to open these applications before running.


Laptop battery Test Method 2: Buy special test software to be certified as Brand Mobile. HP Pavilion dv9000 Battery It is by running some special programs to test your endurance of the battery cell. And it is often more tests save system resources. Sometimes playing Unreal Tournament (Unreal Tournament) The class of the game, if using Mobile Mark test data to estimate the lifetime of the battery is not an easy task. Mobile Mark also provides a feature called the reading test, it can mimic the user to view a page of text file, and his results speak for your notebook batteries in the use of minimal loading time.


However, I believe that the use of mobile professionals Mark test software must be quite expensive, using the program monitors motherboard also appeared not specific enough, so here we recommend a battery of testing new software - PC Portable battery of tests of software-Battery Eater.


Test software on the laptop battery Battery-Eater


Mobile software test Dell Inspiron E1505 battery-Battery Eater is a software specifically for the X-test bitlab developed in the laboratory. With this simple procedure and practice, we can not only test the laptop batteries in different work environments where the potential can also use this software generates various tables and graphs to include a variety of test data and configuration information of ‘computer.


Until 2002, December 20, HP EV087AA Battery after a number of improvements needed and perfect after, Battery Eater the first edition was published. At that time, the first information of user feedback indicates that the software should also continue to improve, so that the second edition of the software Battery Eate is quickly delivered. HP Pavilion dv9000 Battery(hp dv9000 battery), HP EV087AA Battery, On January 5, 2003, 2003 Battery Eater X-bitlab the first laboratory official release. Hou then start the software on the new report system configuration, status indicators for hp 417066-001 battery charging and maps of battery discharge and other functions. Is even more gratifying is that BatteryEater available for free download.


As we all know that many non-profit software usually remain in the initial test version and would never consider going to improve, although a little bit. This software Battery Eater is on the contrary, it is up to date has been made several improvements and perfection. This little program was included in the site of much free software, and after a number of web site column and test

2009年11月18日星期三

for your Bacteria Battery

Those electronic gadgets on many shoppers' holiday lists seem to be getting more and more high tech, but they still run on old-fashioned batteries.Sony laptop battery As this ScienCentral News video reports, instead of ending up in the trash, the batteries on your future shopping list may run on trash.


A New Kind Of Battery


For some time scientists have been interested in toshiba tecra a8 battery figuring out ways to put waste materials and garbage to work by converting the trash into electricity.Sony VGP-BPL2 Battery, Sony VGP-BPS3 Battery, Sony VGP-BPS5 Battery, Now a team of researchers at the University of Massachusetts–Amherst has discovered a new bacteria that can do just that and run a new kind of battery.


“At its present status we can run simple electronic equipment such as a calculator or a very small light bulb,” says Derek Lovley, an environmental microbiologist who led the research.


The micro-organism, Rhodoferax ferrireducens, feeds on simple sugars like sucrose, fructose and glucose, which are found in such things as fruits, beets and sugar cane. It will also feed on xylose—a part of wood and straw—and as long as it has a food source the microbe is self-sustaining,Lovley brought the micro-organism, found in sediment from a Virginia aquifer, back to his lab and designed a simple two-compartment fuel cell. “The way the battery functions—it’s basically a solution of sugar, just like the table sugar you would put on your cereal,” says Lovley. “It’s in water, we dip [an electrode] in that sugar solution… and add these micro-organisms. The micro-organisms attach onto the electrode surface and start to grow by using that sugar.Sony VGP-BPS3 Battery And at the same time they are growing and metabolizing the sugar, they are transferring electrons onto the electrode surface, producing electricity pcga-bp2nx ,pcga-bp2ny."


Surprising Results


What this micro-organism could do surprised Lovley and his team. “I think the fact that micro-organisms could carry out this kind of process was pretty amazing and not expected”, says Lovley. “Because for micro-organisms to accomplish this electricity formation, they have to transfer the electrons outside their cell and that’s just not something most life forms are able to do.”


R. ferrireducens belongs to a group of recently discovered micro-organisms known as “iron-breathers” —so-named because they evolved the strategy of iron respiration. Found in sediment where oxygen is scarce, they use iron for metabolic energy just as humans use oxygen to burn food.


Many research groups have been pursuing a useable biofuel cell that is powered by microbes, but have been vexed by low returns and the need for additional toxic compounds to make the reaction work. Lovley’s bacteria does the work all by itself gk479,fk890,Sony VGP-BPL2 Battery, Sony VGP-BPS3 Battery, Sony VGP-BPS5 Battery, dell inspiron 1520 battery , dell inspiron 1521 battery.


“Our process does not require the addition of any toxic chemicals in order to help the electrons get transferred from the micro-organism to the electrode,” says Lovely.


Next Steps


Lovley sees this as another possible and practical solution for generating energy from alternative fuel sources, Sony VGP-BPS5 Battery but points out that there is still a lot of work to be done. “I think it’s important to realize that we’ve now just proved the concept. There’s certainly a lot of engineering to go into developing this for commercial application, but it’s a fairly neat thing to see that you can just use a micro-organism in this way for some practical benefit.”


Lovley hopes that his “bacterial battery” may one day have many uses, like powering sensors in remote places where it's difficult to change traditional batteries, or in household devices, where one could convert grass clippings into power for an electric lawn mowerdell inspiron 1720 battery , dell inspiron 1721 battery

Super Laptop Battery

Ever wish you could charge your cellphone or laptop in a few seconds rather than hours?Sony laptop battery
As this ScienCentral News video explains, researchers at the Massachusetts Institute of Technology are developing a battery that could do just that, and also might never need to be replaced.


The Past is Future


As our portable devices get more high-tech, the batteries that power them can seem to lag behind. But and his team at plan to make long charge times and expensive replacements a thing of the past--by improving on technology from the past d5318,u4873,dell inspiron 6000 battery.


They turned to the , which was invented nearly 300 years ago.Sony VGP-BPS8 Battery, Sony VGP-BPS9 Battery, Sony VGP-BPS10 Battery, Sony PCG-R505 Battery, Schindall explains, "We made the connection that perhaps we could take an old product, a capacitor, and use a new technology, nanotechnology, to make that old product in a new way."


Rechargable and disposable batteries use a chemical reaction to produce energy. "That's an effective way to store a large amount of energy," he says, "but the problem is that after many charges and discharges ... the battery loses capacity to the point where the user has to discard it."


But capacitors contain energy as an electric field of charged particles created by two metal electrodes. Sony VGP-BPS8 Battery Capacitors charge faster and last longer than normal batteries. The problem is that storage capacity is proportional to the surface area of the battery's electrodes, so even today's most powerful capacitors hold 25 times less energy than similarly sized standard chemical batteries dell inspiron 9300 battery ,dell inspiron 9400 battery.


The researchers solved this by covering the electrodes with millions of tiny filaments called . Each nanotube is 30,000 times thinner than a human hair. Similar to how a thick, fuzzy bath towel soaks up more water than a thin, flat bed sheet, the nanotube filaments increase the surface area of the electrodes and allow the capacitor to store more energy. Schindall says this combines the strength of today's batteries with the longevity and speed of capacitors.


This technology has broad practical possibilities, affecting any device that requires a battery. Schindall says, "Small devices such as hearing aids that could be more quickly recharged where the batteries wouldn't wear out; up to larger devices such as automobiles where you could regeneratively re-use the energy of motion and therefore improve the energy efficiency and fuel economy."


Schindall thinks hybrid cars would be a particularly popular application for these dell inspiron xps m170 battery ,dell inspiron xps m1710 battery batteries, especially because current hybrid batteries are expensive to replace.


Schindall also sees the ecological benefit to these reinvented capacitors. According to the ,Sony PCG-R505 Battery more than 3 billion industrial and household batteries were sold in the United States in 1998. When these batteries are disposed, toxic chemicals like cadmium can seep into the ground.


"It's better for the environment, because it allows the user to not worry about replacing his battery," he says. "It can be discharged and charged hundreds of thousands of times, essentially lasting longer than the life of the equipment with which it is associated."


Schindall and his team aren't the only ones looking back to capacitors as the future of batteries; a research group in England advances of their own. But Schindall's groups expects their prototype to be finished in the next few months,Sony VGP-BPS8 Battery, Sony VGP-BPS9 Battery, Sony VGP-BPS10 Battery, Sony PCG-R505 Battery, and they hope to see them on the market in less than five years.


Schindall's research was featured in the May 2006 edition of and presented at the 15th International Seminar on Double Layer Capacitors and Hybrid Energy Storage Devices in Deerfield Beach, Florida on December 2005. His research is funded by the pa3285u-1brs,pa3285u-2brs,pa3284u-1brs,toshiba tecra a1 battery .

power battery R&D

Zhongke Ying R & D into the field of power battery

Zhongke Inventec (600110, closing price of 7.32 yuan) today released the assets of the acquisition announcement. Notice indicates that the company invested 38 million yuan will be a subsidiary of Beijing to acquire a sub-power battery R & D Co., Ltd. 100% equity. Sony laptop battery Market analysts believe that has already begun to set foot in the field of new energy in terms of Section Inventec, which undoubtedly will make the company's new energy a more complete industry chain fru 92p1121 , fru 92p1123 , fru 92p1125.


Asia 38 million to buy a stake in power

Notice shows that June 9, 2009, the company wholly-owned subsidiary in Beijing Yinghua Technology Development Co., Ltd. Branch (hereinafter referred to in Section Beijing) and Shu-Jun Li, Li Yan-ming signed "share transfer agreement."


Under the agreement, Beijing Sino-Kuwaiti investors to buy 38 million yuan, respectively, Shu-Jun Li, Li-Ming Beijing held a sub-power battery R & D Co., Ltd. (hereinafter referred to as a sub-power) Total 100% of the equity. Of these, 15 million yuan invested to acquire record held by Mr. Li Shujun Asia 39.47% stake in power; financed the acquisition of 23 million yuan held by Mr. Li Yanming a sub-60.53% stake in power. Asia driving force for the purchase price in order to create value for the reference for the audit, 1 yuan per share pb991a, hp business notebook nc4200 battery.


Statistics show that the main driving force for operation of a sub-power batteries and battery combination of R & D, production and sales. With the global increase in demand for new energy sources, the company is committed to new energy sources, such as electric vehicles, such as R & D motive power batteries, production and sales, the industry prospects.


The company said the main driving force for the acquisition of the purpose of sub-hit is based on the company's "industrial chain" strategies, Sony PCG-V505 Battery focusing on electronic information industry development of electronic materials and new energy infrastructure of ideas, with the company formed the industrial chain of copper products. The acquisition of the capacity of the company's continuing operations and industrial development have a positive effect.


The layout of the new positive energy

Electric cars are the future of automotive development. Electric vehicles and lithium batteries in electronic devices and applications more copper, copper foil industry development prospects. Statistics show that in Ying Wa Branch will start at the beginning of 2007 million tons of copper foil of the Qinghai plan.

By the end of March that year, Inventec Appliances and the West Branch of Mining Group signed a strategic cooperation agreement, the two sides plan to joint venture the construction of 10,000 tons annual output of copper projects. To this end, the company launched in July was about 10 billion of additional program-oriented. However, the end of 2007 the market situation changed, and Inventec Appliances Division at 17.21 yuan per share, in the west-oriented mining group shares issued after 2600, due to non-public offering price less than the reserve price, investors therefore directed to other specific issues forced to cancel plans. In addition to orientation of additional financing, in Section Inventec advance through bank loans million tons of electrolytic copper project hp business notebook nc4400 battery , hp business notebook tc4200 battery , hp business notebook tc4400 battery.


It is learned that the company's lithium-ion battery electrolytic copper foil with the top domestic market to 50%, at the same time,Sony PCG-Z505 Battery the company has successfully developed the car with extra-thick copper circuit boards have begun to enter the market, production capacity is about 2100 tons per year; company of high-grade copper project is the national "863" program of scientific and technological achievements into mass production projects, a shortage of products in the domestic growth. With the international advanced level and independent intellectual property rights of extra-thick copper foil production capacity of about 2100 tons per year; company holds 75% stake in the joint realization of Copper Co., Ltd. 2007 revenues 175,544,600 yuan, 37,512,300 yuan of Maori to achieve a net profit of 2797.77 million.


Market analysts said: "The company recently a new field of energy distribution, the acquisition of a new Asian power will improve energy industry chain. In addition to the concept of new energy sources, but also has a venture capital, the concept of resources, multi-theme is expected to funds by the market of concern hp pavilion dv7 battery,hp pavilion dv8000 battery,395789-001,hstnn-db20.

2009年10月8日星期四

User Reviews Of HP Compaq Business Notebook NC6200

User Reviews Of HP Compaq Business Notebook NC6200

Screen Size: 14.1 inches

Weight: 5 lbs

Processor Options: Intel Pentium M

Graphics Options: Integrated



• Includes Microsoft® Windows® XP Professional or Microsoft® Windows® XP Home

• Intel® Pentium® M processors or Intel® Celeron® M processors Sony laptop battery
Sony PCGA-BP1N Battery, Sony PCGA-BP2NX Battery, Sony PCGA-BP2NY Battery,

• 15.0-inch XGA (1024 x 768 resolution and 16 M colors) or 15.0-inch SXGA+ (1400 x 1050 resolution and 16 M colors)

• One fixed optical drive

• Starting at 6.06lbs and 1.2-inches thin

• Intel® Graphics Media Accelerator 900,Sony laptop battery up to 128-MB shared system memory

• Battery: PB994A





Powerful, neat, small, portable laptop! I love it!

Submitted by Rogarhcard

Rating: 8/10

Pros: I love this laptop compared to all my other friends and collegues laptops.Sony laptop battery
Sony PCGA-BP1N Battery, Sony PCGA-BP2NX Battery, Sony PCGA-BP2NY Battery, I like that its 14.1" screen size...not too small and not too large and cumbersome. It is also very thin, but it is extremly sturdy, even though sometimes I think I might be holding it in one hand too much. It is light compared to all my friend's laptops. I am a graduate student, and it portays a business minded image. I have had no stability issues. It has performed flawlessly for me thus far. I am currently upgrading the RAM from 512MB to 1.5GB.Sony PCGA-BP2NY Battery, I do not have any issues with the 512 for my usage, I am just greedy I guess. FEATURES I LIKE: -Ambient Light Sensor: which automatically adjust the brightness of the screen acording to ambient lighting present -Built in SD card reader -Both pointing stick and touchpad -one touch presentation button -onboard mic -Security lock feature which can also be set to lock your hard drive permanently in case you have highly sensitive data on your hard drive. Overall, I am in love with this laptop. I hope it give me many more years of trouble free service.


Cons: no on-screen display of volume meter, can not get my bluetooth to work ( I do not have much use for it though)


A Solid Performing Business Notebook


Submitted by Antedkuead


Rating: 7/10


Pros: This is an excellent business notebook that has a great keyboard, Sony PCGA-BP2NX Battery,good performance, and simple design. I have yet to find any features that irritate me enough to return the notebook, and I have been through at least 4 notebooks looking for the right fit. The NC6200 series is a great alternative for anyone looking to buy a business notebook with a ThinkPad design. It is my opinion that this notebook has a better build that the ThinkPad T43. The T43 has a poor build, Sony laptop battery
Sony PCGA-BP1N Battery, Sony PCGA-BP2NX Battery, Sony PCGA-BP2NY Battery,especially on the palm rest that creak with constant motion and pressure. The NC6200 series has a completely solid feel.


Cons: Battery(HP COMPAQ PB994A) performance is ok, but for a business notebook battery performance should be more of a focus. Sony PCGA-BP1N Battery,Lack of an intergrated fingerprint reader and built in microphone. Additionally, the edges of the notebook should be smoother, especially around the palm rest.

Compaq Presario R3000

Compaq Presario R3000

Spec data:

1.6-GHz Athlon XP-M 3000, 256MB DDR SDRAM, 40GB (4,200-rpm hard drive, 15.4-inch (1,280 x 800) display, 802.11b wireless, 7.9-pound system weight (9.5-pound travel weight), nVidia GeForce 4 420 Go graphics, DVD/CD-RW combo drive, three USB 2.0 ports, Windows XP Home



Pros:

Wide-aspect screen, three USB ports, easily accessible buttons.

Cons:

(compaq r3000 battery) (COMPAQ 346970-001) life: 4 - 6 hours

Bottom Line:

the HP Compaq Presario R3000 is a desirably designed multimedia notebook, with a 15.4-inch wide-screen display at an affordable price.



Review

If you're looking for a bargain basement system to ease the back-to-school burden but don't want to sacrifice multimedia features, then the Compaq Presario R3000 could be the notebook for you.


The 8-pound R3000 has a sharp 15.4-inch WXGA display. The system had no problem displaying our test DVD movie clearly, and its JBL Pro speakers delivered superb sound quality. The nVidia GeForce4 420 Go graphics solution helped the R3000 win first place on our 3D performance tests. (Although our test system came with 802.11b, HP is offering free upgrades to 802.11g.)


On Multimedia Content Creation Winstone and our Serious Sam SE gaming demo, the R3000 had the best scores of the budget machines with 16.6 and 28.4, respectively. But we were surprised to find no memory card reader on a system with such multimedia-centric components. HP Presario R3000 Battery On Battery Mark, the R3000 lasted 4 hours 42 minutes, which was lowest among the budget systems.


The R3000 offers very good bang for the buck if you're on a budget but still want a spiffy multimedia system that will impress your dormmates. (Hey, you even get Microsoft Office SE 2003 for when it's time to get to work.) Shy away from the R3000, however, if you're looking for a more mobile system to carry around campus.

2009年9月23日星期三

Methanol fuel cell & multi-purpose portable solar

2004 to 2005 as the target market, the Japanese equipment manufacturers around the laptop battery and cell phone fuel cell engaged in a fierce competition to develop. Fujitsu Research Institute in the trial of this case for fuel cell laptops.Hp laptop battery Maximum output power of 15W, in the use of 300ml of methanol solution, they can drive the company's notebook computer "FMV-BIBLOMG55E" running from 8 to 10 hours. Since 2001 the Institute began in the materials before and after the Environmental Technology Institute of the fuel cell for mobile phone development, has made some in the outcome of the test products will be announced later. HP Pavilion ZV6000 Battery(hp zv6000 battery)
HP Pavilion DV1000 Battery(hp dv1000 battery), HP PF723A Battery, HP 367759-001 Battery, The test products released for notebook computers, but not solely on the development of personal computers for the goal. "Mobile phone and other mobile devices will be equipped with features such as television receivers, the power consumption will continue to improve. Naturally applies to the equipment, taking into account" (Fujitsu Research Institute of Materials Research Institute of Environmental Technology Research Department of the function of organic materials). Entering the practical stage, will be considered with the mobile phones, notebook computers and other joint business development.


The advantage of the introduction of the test products is promising to use high concentration methanol solution. In the original direct methanol fuel cell, if the supply of fuel very high concentration of methanol solution, the methanol will not react directly through the polymer electrolyte membrane, the occurrence of "infiltration (CrossOver) phenomenon." Therefore, at present, most of the set concentration of methanol solution at about 10%. Fujitsu Research Institute of the confirmation, even if the concentration of methanol solution to 30% toshiba battery, it did not happen due to infiltration of the phenomenon led to the problem of declining output. Due to high concentration of methanol can be used,HP Pavilion ZV6000 Battery(hp zv6000 battery) thus greatly improving the unit weight or unit volume of energy density.


In order to reduce the infiltration phenomenon, Fujitsu Research Institute has done a two-pronged effort. Polymer electrolyte membrane that is to change the composition of the material, HP Pavilion ZV6000 Battery(hp zv6000 battery)
HP Pavilion DV1000 Battery(hp dv1000 battery), HP PF723A Battery, HP 367759-001 Battery, as well as efforts in the electrode structure. The use of polymer electrolyte membrane material has aromatic structure of the main chain. The original widely used fluorinated resin as compared to the spatial structure of polymer is very different. "This kind of material to make polymer electrolyte membranes become rigid and detailed. Feel like on the stronger and engineering plastics. And also very strong polarity. Mission of methanol polymer electrolyte membrane had preventive effect of increased 5-fold" ( Fujitsu Research Institute). Through the use of such a polymer electrolyte membrane, even if the concentration of methanol kept at 30%, it did not happen due to the infiltration phenomenon caused by the phenomenon of decline in output power. Fujitsu Research Institute also said that "feeling can also continue to improve concentration. Has confirmed in 40% of work", but did not mention the use of methanol and, therefore, a high concentration of methanol is not clear how efficient the use of. battery.


In order to obtain such a polymer electrolyte membrane material, the Institute with the outside world in addition to factories and universities to conduct joint studies, also conducted its own internal development. Fujitsu Research Institute but did not publish the source of the materials used,HP Pavilion DV1000 Battery(hp dv1000 battery), and ultimately used to determine what kind of material did not.


In the electrode structure, the Au catalyst is said to improve the density of carbon black carrier. "Improving the density of the outer electrode. The result is compared with the original electrode makes the thinning. Au particles larger density, the physical structure also helps prevent the passage of methanol molecules" (Fujitsu Research Institute). For the realization of such a high-density, it is said the company will be fine Au particles to the diameter of 2 ~ 3nm.


Fujitsu Research Institute will present the concentration of methanol solution to 30%, but their goal is 50%. "30% is not enough. If you do not raise the 50 percent target is not" (Fujitsu Research Institute). Practical use of the target before and after 2005.


Fujitsu Research Institute in the development, HP Pavilion ZV6000 Battery(hp zv6000 battery)
HP Pavilion DV1000 Battery(hp dv1000 battery), HP PF723A Battery, HP 367759-001 Battery, it is also expressed at home and abroad to participate actively in the legal environment to promote the idea that "although progress has been made in the development, if imperfect legal provisions, in the application of obstacles still exist. For example, HP PF723A Battery,when the fuel cell with into the aircraft cabin? it is necessary to advance the preparatory work in this area. "


Add the use of methanol fuel solution. Solution penetrated into the lower part of the adoption of self-respect toshiba satellite m100 battery, toshiba satellite m105 battery, it reached the bottom of the fuel cell plate. Solution in methanol without added tools such as pumps, belonging to the passive type.


The products include the body (battery), solar cells, a variety of devices to connect the dedicated AC wire interface. Electricity generated by solar cells is stored in the body, the use of stored energy, the solar cells can be removed in order to carry. Capacity of the power can be stored 4.8Wh, equivalent to two ordinary phone battery. Output voltage of 3.8V ~ 8.5V, the maximum output power of 10W.


Part of solar cells using a single two large-size solar cell modules. Generating high-voltage generally is 7mm width of 15 battery modules in series to constitute a loop, but this will appear as part of the battery unit according to less than sunlight, or by an external impact damaged part of the battery unit of the circuit can not work. To avoid this problem using a single mode of NTT.


Removed after the solar cells can be placed on a hand


However, in SBC, the use of sunlight can be issued only voltage 0.1 ~ 0.4V or so.HP 367759-001 Battery, NTT has developed to this end will be about 0.1 ~ 0.4V low-voltage to 5V or so "very low input-voltage step-up technology." In order to achieve even a part of the plate can not generate electricity to other parts of the normal power generation, and will have the power stored in batteries on the body of the function, the entire solar cell modules are printed on the collection of the electrode power.


In addition, the "pockets of power," also called with the "MPPT" (Max Power Point Tracking) function. It can detect changes along with the light of current and voltage changes, it has been maintained at the highest state of power generation. "MTTP is a roof, etc. have been used in solar cells on large-scale practical use of technology, HP Pavilion ZV6000 Battery(hp zv6000 battery)
HP Pavilion DV1000 Battery(hp dv1000 battery), HP PF723A Battery, HP 367759-001 Battery, but because of the control chip power consumption is too large can not be used in the previous small-scale solar cells.'s" Power pockets "to streamline the functions of the MPPT successfully configure the function "(NTT Energy Research Institute of Environmental Systems Engineering, director of energy research fellow Masato Mino). NTT said that through these technical improvements, new product capabilities in power generation technology with the use of the original compared to the power-generating capacity, photoelectric conversion efficiency can be increased by about 1.5 times.

Contend with fuel cell vehicle

Speaking of a new generation of cars, the most powerful when the number of candidates in order to hydrogen-powered fuel cell vehicle laptop battery. However, there are many issues compared to the fuel cell vehicle,Hp laptop battery there are a number of new technologies and as a result of more realistic and compelling. This is the electric motor with the engine and the hybrid, as well as in Europe, promoting the popularization of the main diesel engine vehicles.


In these new technologies and intense competition for dominance in the competition when it unexpectedly From a surprise. This is the Mazda is developing a "hydrogen rotary engine" car.


To ¥ 5,000,000 each (about 384,000 yuan) for the target


Fuel cell vehicle is hydrogen and oxygen through a chemical reaction to obtain power, and Mazda's hydrogen engine is based on hydrogen-fueled internal combustion engine. The world dedicated to research and development of hydrogen engines only Mazda and BMW in Germany. Mazda since 1991, HP PM579A Battery, HP Pavilion DV4000 Battery(hp dv4000 battery) , HP Pavilion ZE2000 Battery(hp ze2000 battery), HP Presario M2000 Battery(compaq m2000 battery), has been engaged in the development of hydrogen engines. Up and down movement of the piston engine general it is difficult to control the combustion of hydrogen toshiba battery. However, HP PM579A Battery,Mazda's proud ---- let alone technology triangle rotating rotor rotary engine is very suitable for control of hydrogen combustion, hydrogen engine is Mazda eyes on this point.


"The goal is 3 to 4 years in the practical operation." In October last year, Mazda's president Hisakazu Imaki in Tokyo Motor Show this Declaration issued Zhuang, before the specific surface of the strategic plan. The next 2 years with a hydrogen engine will be the first to government agencies and enterprises to carry out video, then consider selling in the market. February next year will add an additional hydrogen Mazda headquarters facilities for the practical use to prepare. In addition, the need to spend huge sums of money from the fuel cell vehicle Mazda's largest shareholder - the United States responsible for the development of Ford, it can be wholeheartedly Mazda hydrogen rotary engine development. Rotor hydrogen car is the most important weapon to reduce costs. At present, such as Toyota and Honda are rented or sold to government agencies, such as fuel cell vehicle, but the body is said to vehicle prices in the ¥ 100,000,000 (about 7.69 million yuan) or more. Fuel cell vehicles as a key part, so that hydrogen and oxygen react chemically generate electricity, "battery pack" in terms of cost to occupy a large proportion of future development work still needs to invest heavily.


At the same time, hydrogen basic structure of the rotor of motor vehicles in April last year began selling sports car of the "RX-8" compared to almost no change. Just add an additional hydrogen to the combustion chamber of the injection device, placed in the trunk of the hydrogen storage tank and the hydrogen leak detection sensor can be.HP Pavilion DV4000 Battery(hp dv4000 battery) , Even the engine room, compared with an ordinary car is no different, you can use the original intact production equipment to reduce new investment.


RX-8 in the prices of ¥ 2,000,000 (about 150,000 yuan) from top to bottom, and "practical rotor of the hydrogen car will be the market price of about ¥ 5,000,000 in the objective to develop" (project development to promote this Investigator Zhanghong Kashiwagi). It is certain that the low supply prices will be fuel cell vehicles can not match.


Hybrid is also under consideration


Kashiwagi full of looking forward to the future: "Hydrogen is not a simple rotor 'convergence' petrol truck and a car battery technology. Hydrogen supply facilities in the future even if fuel cell cars have become the mainstream of the times, but also need to use, so the rotor hydrogen fuel car can be cell vehicles continue to coexist. "


However, the true hydrogen car to universal rotor that there are still some technical issue toshiba satellite m40 battery, toshiba satellite m45 battery. Rotor current development of hydrogen cars, hydrogen can only be added once traveling 70km. Although it could be combined with gasoline, in the practical aspects of the problem does not exist, but such a short distance or to undermine the significance of the next generation of engines. In addition, the use of gasoline can produce 210 horsepower at the power, and then switch to hydrogen is only about 110 horsepower, HP PM579A Battery, HP Pavilion DV4000 Battery(hp dv4000 battery) , HP Pavilion ZE2000 Battery(hp ze2000 battery), HP Presario M2000 Battery(compaq m2000 battery), a reduction of about half the horsepower. Even if these problems can be solved, but "still need to study hydrogen storage battery and the motor rotor and the combined hybrid system." (Okada and Mazda's executive director)


Rotor engine in the 90's have had to stop the development of endangered plight. HP Pavilion ZE2000 Battery(hp ze2000 battery),It difficult to cope with increasingly stringent environmental standards are the main reason. However, this is the rotor Mazda engine may become a new generation of environmental technology trump response.


U.S. R & D of micro-generators to replace the phone battery


Recently, the USA and Georgia Institute of Technology announced that with the Massachusetts Institute of Technology, working closely with scientists, they have successfully developed a micro-generators, only 10 mm in diameter, is the continuing use of mobile phone battery is more than 10 times. Scientists will be held in January next year, the International Conference on Micro Electro Mechanical System published the results of this gratifying.


Georgia Institute of Technology is one of 10 open construction, computer, engineering, management and other professional, a total of 16,000 students in the United States is to train African-American women scientists and the best scientists, a university, research university is 2003-2004 academic year a total of 342 million U.S. dollars of research funding.


Over the years, more and more compact electronic products, and its battery has a larger volume of plays. In order to solve this problem, the scientists have been dedicated to the development of micro-generators, and put forward a number of different principles of micro-generators. And the Georgia Institute of Technology scientists have developed such a generator to replace the phone toshiba satellite m50 battery, HP PM579A Battery, HP Pavilion DV4000 Battery(hp dv4000 battery) , HP Pavilion ZE2000 Battery(hp ze2000 battery), HP Presario M2000 Battery(compaq m2000 battery),toshiba satellite m55 battery, indicating that micro-generators to enter the electronic products to replace conventional batteries and an important step.


The principle of the micro-generator is installed in a chip on the induction coil, so that a small rotating magnet around the coil, resulting in sufficient current. Through continuous testing, the rotating speed of the magnet is now up to 100,000 per minute lap,HP Presario M2000 Battery(compaq m2000 battery), the speed can generate 1.1 kilowatts of electricity, enough to replace the phone battery. The researchers said that will be sure to have a speed of 20-50 kilowatts of power for laptop computers. In order to improve the rotation speed, the most critical problem is how to avoid rotating magnet in the process of fracture. Centrifugal force generated by high-speed rotating magnets broken enough to make, in order to solve this problem, researchers continue to improve the size of magnet and wrapped in titanium alloys in.

New type of lithium battery electrolyte

Institute of Advanced Industrial Science and Technology in Japan developed a lithium-ion rechargeable laptop battery for the flame-retardant electrolyte. Hp laptop battery Not volatile as a result, even if the temperature of +300 ℃ will not be close to the fire and decomposition, but also not in the ordinary lithium-ion rechargeable battery voltage of the chemical reaction. Will be applied to lithium metal anode for lithium-ion rechargeable batteries can greatly enhance the safety of use.


The development of electrolyte for maintaining the liquid state under normal temperature and the organic salt "ionic liquids." Specific components for the four cyclic amine - amine salt PP13 ㏕ FSI (N-methyl-N-proplylpiperidiniumbis (trifluoromethanesulfonyl) imide).HP Presario V2000 Battery(compaq v2000 battery), HP pavillion zx5000 Battery(HP hp zx5000 battery), HP PP2200 Battery
HP Pavilion dv2000 Battery(hp dv2000 battery), Not only has the non-volatile and fire retardant, and will not precipitate a lithium metal anode for lithium-ion rechargeable toshiba battery, when often the dendritic crystallization (dendrite). The original organic solvents as a result of repeatedly charging generated power and dendritic crystal would result in the compartment between the electrode punctured causing a short circuit. The development of ionic liquids will not be such a dendritic crystal precipitation, but relatively smooth

To.

The development of the use of electrolytes to lithium metal as negative electrode,HP Presario V2000 Battery(compaq v2000 battery), lithium cobalt (LiCoO2) for the positive electrode of the button battery charge and discharge more than 97% efficiency, the effect was very good. In addition, a nickel electrode plate for easy battery trial units (according to charge type unit) charge-discharge efficiency was also achieved in the test more than 97%, with the original organic electrolyte maintained essentially at the same level. Institute of Advanced Industrial Science and Technology that, in addition to lithium metal used in electrodes for lithium-ion rechargeable battery, this electrolyte can also be used to improve the existing lithium-ion rechargeable battery security. As a result of new low electrolyte conductivity, so the issue is how the future with other electrolytic

All to be improved and so on.


The results as a New Energy and Industrial Technology Development Organization (NEDO Technology Development Organization) project commissioned by the "fuel cell vehicles, such as lithium-ion battery technology development - elements of high-performance lithium battery technology development (2002 ~ 2006)" and to conduct research.


Singapore developed a nano-size of only 50 transistors


According to reports, the success of Singapore scientists have developed nano-size of only 50 transistors, so that Singapore's semiconductor research from the "micro-electronic" era into the "nano-electronic" era.


The study was the National University of Singapore Associate Professor of Electrical and Computer Engineering, led by Yang Jia Microelectronics Institute of the two groups and results of cooperation. Institute of Microelectronics,HP Presario V2000 Battery(compaq v2000 battery), HP pavillion zx5000 Battery(HP hp zx5000 battery), HP PP2200 Battery
HP Pavilion dv2000 Battery(hp dv2000 battery), Singapore Science, Technology and Research under the research institutions.


Dr. Yang Yujia accepted an exclusive interview with the newspaper said, roughly equivalent to 50 nanometer diameter 1/2000 hair,HP pavillion zx5000 Battery(HP hp zx5000 battery), about the size of 100 atoms. Estimated the speed of its operation than the existing transistors 20-50% faster.


Yang Jia said, it is worth mentioning is that the transistor can be directly integrated into existing chip manufacturing process of the disc toshiba tecra a3 battery, toshiba tecra a4 battery. Wafer fabs in its production process as long as the added two steps, you can create such a transistor, rather than have the trouble and equipment replacement process.


Transistor is the electronic products such as computers, mobile phones, digital cameras, such as an important part. The size of transistors and operating speed, it will directly affect the prices of electronic products and functions. If a circuit can accommodate more transistors, but also means that the functions of electronic products more stronger. Transistors with lower power consumption, have a direct impact on battery life of electronic products.


Dr. Yang said that in the microelectronics era of transistor manufacturing process had not reached the level of atoms. "About two or three years ago, the transistor has such a small extent: HP Presario V2000 Battery(compaq v2000 battery), HP pavillion zx5000 Battery(HP hp zx5000 battery), HP PP2200 Battery
HP Pavilion dv2000 Battery(hp dv2000 battery),scientists must begin to study how atoms arranged in order to create smaller transistors."


Nanoelectronics refers to artificial changes in the distance between atoms to create a smaller and better transistors.


AEM made Shanghai Fengbao proxy Chip Fuse


Agent components and Shanghai Electronic Technology Co., Ltd. has recently introduced a new chip fuses the United States AEM product line, the protection circuit for the user to provide more choices.


It is said, AEM in laminated ceramic chip electronic components, HP Pavilion dv2000 Battery(hp dv2000 battery),thick film technology, new materials and electronic components design and manufacture of proprietary equipment, such as the industry leader in the field. The company is the U.S. Department of Defense and NASA (NASA) satellite dedicated space approved FM12 fuses the world's sole supplier of top U.S. priority in the purchase of military products supplier directories. AEM has also won numerous clients such as the U.S. company TRW awarded "Best Supplier" award.


The abundance and the Shanghai Electronic key is to promote SolidMatrix shaped surface mount chip fuse (lead-free). AEM developed SolidMatrix alone produced stone-type fuses, the use of the AEM "co-firing" (co-fired) patented technology, with a structure, high reliability and low manufacturing costs, etc., can be widely used in liquid crystal displays, PC card, floppy disk drive, PDA, digital camera, DVD, television, cell phones, rechargeable toshiba tecra a5 battery, toshiba tecra a6 battery, battery charger circuit protection products.


The new lithium-ion rechargeable battery cathode materials

The new lithium-ion rechargeable battery cathode materials


Sanyo Electric recently successful trial using a new generation of lithium-ion rechargeable laptop battery cathode materials for the candidate - LiFePO4 battery,dell laptop battery and in “the 45th Battery Symposium” published the contents of the security.


The characteristics of LiFePO is: LiCoO2 cathode materials with the existing compared to lower-cost materials and high temperature will not release oxygen, thus the high security. In addition to Sanyo Electric, the seminar on the five research institutions have published the relevant results of basic research has been in full swing. For example, the University of Tokyo Institute of Technology announced the fast charge characteristics of LiFePO4. However, most of these studies remain in the pilot phase electrode, the battery can be used for the actual evaluation of the electrode characteristics has not yet begun. Sanyo Electric and the trial of a diameter of 18mm, high 65mm cylindrical toshiba batteries, and battery on the security characteristics of the test. The use of a graphite anode.


Safety test in the detection of the trial cylindrical barbed nail cells and the circumstances Overcharge.Y9943 Battery, Spurs to nail after 30 seconds the temperature rose to about +110 ℃, but then did not continue to rise, but slowly falling down. Charge during the test, 6T473 Battery
Inspiron 630m Battery, Inspiron 640m Battery, Y9943 Battery,as a result of charging excessive electrolyte decomposition temperature up to +120 ℃, while playing an open valve immediately after the power was cut off. From the above results, obtained in the security issues and there is no significant conclusions. Battery characteristics to 0.25A for discharge, the discharge capacity of 1095mAh, the energy density per unit volume for 214Wh / l, the energy density of unit weight for 96.5Wh / kg.


Issues currently faced by the characteristics of low temperature low. +60 ℃ at 96mAh, +25 ℃, when a discharge capacity of 888mAh to 0 ℃ will dramatically reduce the 375mAh. At the meeting, someone asked directly: “LiFePO4 there so many problems, there will be attractive to you? Have hoped to put in actual use it?.” In this regard, speakers from a personal point of view, said: “In addition to previously noted that the problem of low electronic conductivity,Inspiron 640m Battery this time found a low-temperature characteristics of the problem of low, I personally feel that the future emergence of new issues.”


Canon to launch small-scale fuel cells for hydrogen supply device


Canon developed the use of MEMS technology to create the hydrogen supply device, and in November 29, 2004 ~ 30, held in Kyoto “PowerMEMS 2004″ were released on. Applications for digital cameras and other portable devices on the fuel cell.


The role of hydrogen gas supply device is to preserve high-pressure storage tank of hydrogen needed to release the amount of an atmospheric pressure dropped after the supply to the fuel cell. Its structure and the use of divers to breathe oxygen devices like the valve is very common (Canon). MEMS technology will be adopted to reduce the size 8mm × 8mm × 1mm.


The use of hydrogen gas supply device to the 300μm thick silicon films plus 3 stacked structure.Inspiron 630m Battery, With hydrogen pumps connected to the bottom with a single-chip switch, the resulting hydrogen gas to enter through the middle layer of the channel to form a single-chip into the top single-chip, single-chip from the top of the hole supply to the fuel cell. First single-chip top-level processing toshiba satellite m40 battery, toshiba satellite m45 battery, with the middle layer to the stacked-on-chip processing, 6T473 Battery
Inspiron 630m Battery, Inspiron 640m Battery, Y9943 Battery,the final class with the most single-chip stack processing.


The lower silicon chip switch installed into the diameter of hydrogen 250μm. Through the opening and closing the switch to adjust the hydrogen supply. Released when it is published only in the use of nitrogen can be the result of normal work, it was used to test the hydrogen has been the same result.


Micro-generator can replace cell phone batteries


Georgia Institute of Technology announced that with the Massachusetts Institute of Technology, working closely with scientists, they have successfully developed a micro-generators, only 10 mm in diameter, is the continuing use of mobile phone battery is more than 10 times. Scientists will be held in January next year, the International Conference on Micro Electro Mechanical System published the results of this gratifying.


Georgia Institute of Technology is one of 10 open construction, computer, 6T473 Battery engineering, management and other professional, a total of 16,000 students in the United States is to train African-American women scientists and the best scientists, a university, research university is 2003-2004 academic year a total of 342 million U.S. dollars of research funding.


Over the years, more and more compact electronic products, and its battery has a larger volume of plays. In order to solve this problem, the scientists have been dedicated to the development of micro-generators, and put forward a number of different principles of micro-generators. And the Georgia Institute of Technology scientists have developed such a generator to replace the phone battery, 6T473 Battery
Inspiron 630m Battery, Inspiron 640m Battery, Y9943 Battery,indicating that micro-generators to enter the electronic products to replace conventional batteries and an important step.


The principle of the micro-generator is installed in a chip on the induction coil, so that a small rotating magnet around the coil, resulting in sufficient current. Through continuous testing, the rotating speed of the magnet is now up to 100,000 per minute lap, the speed can generate 1.1 kilowatts of electricity, enough to replace the phone toshiba satellite m50 battery, toshiba satellite m55 battery. The researchers said that will be sure to have a speed of 20-50 kilowatts of power for laptop computers. In order to improve the rotation speed, the most critical problem is how to avoid rotating magnet in the process of fracture. Centrifugal force generated by high-speed rotating magnets broken enough to make, in order to solve this problem, researchers continue to improve the size of magnet and wrapped in titanium alloys in.

Bottleneck in computer ¬ebook batteries

Bottleneck in computer & notebook batteries


With the progress of the notebook battery computer technology,dell laptop battery From a mobile office concept has already become a reality. In order to meet the needs of mobile and mainstream manufacturers are introducing more powerful, more stable system of ultra-thin notebooks. Used for this ultra-thin battery, RC107 Battery
Latitude D620 Battery, 312-0386 Battery, PC764 Battery,but because of the lack of electricity has become a new bottleneck in mobile office. And, in addition to persistent power, the battery is very expensive prices, and a piece of notebook batteries accounted for 10% of the overall price -15%, then an ultra-thin laptop battery should have the characteristics of what it mobile office to meet the demand? From the practical point of view we may wish to analyze the design of laptop battery standard.


Industry experts believe that time is of the battery. Ultra-thin notebook computers because of the thin body makes room for the installation of the toshiba battery becomes more limited, and the battery means to reduce the volume of the power supply even shorter time, not every ultra-thin notebook computers can be up to standard the battery life. At present, a common ultra-thin notebook battery time between 2-3 hours, a good brand can be achieved for about four hours, there are higher, such as NECS820 will be able to provide electricity five hours time, and if equipped with backup battery, the life of up to 11.8 hours. Moreover, the computer which is designed to extend the battery very thin flat-shaped, and its size and the fuselage in line with the expansion of the bottom of the chassis battery integrated with the fuselage,PC764 Battery, and fully maintained the smooth state of the fuselage.


However, even the best batteries, its power can not be unlimited, and the total time spent, and a charge can be completed in the shortest possible time that the battery may be the user’s mobile office to offer as much convenience and efficiency. RC107 Battery
Latitude D620 Battery, 312-0386 Battery, PC764 Battery,Which most users are often easy to forget where the most ordinary laptop charging time is 3-7 hours, with better products to be completed in 2.4 hours recharge.


In addition, some regular users to minimize the use of a variety of components to achieve extended battery life of purpose, for example, do not use CD-ROM, hard disk read as little as possible to reduce the screen brightness or simply dormant and so on. These approaches can indeed maintain the battery a little more time, but “a temporary solution”, select the design of a battery with excellent products, in order to fully enjoy the convenience of mobile office with the fun.


Hybrid battery concern


November 27, 2004 ~ 29, held in Kyoto, “the 45th Battery Symposium” on the hybrid’s rechargeable batteries for concern. During the meeting,312-0386 Battery, held the last day of the “lithium-ion battery (large-scale security review)” At the meeting of many people who can not find seats, not even squeeze into a lot of people standing outside the venue of the lecture. Required on both hybrid high-power density, high energy density and high-wide features such as the practical use rechargeable batteries, Hitachi Vehicle Energy (Hitachi Vehicle Energy), Matsushita Battery Industrial, Yuasa (GS Yuasa) companies such as published the results of the battery trial.


Among them, the Hitachi Hitachi Vehicle Energy and by the success of joint development is the appearance of the size of 108mm × 34mm × 117mm, weighs approximately 770g at right angles to the flat toshiba tecra a3 battery, toshiba tecra a4 battery. Average working voltage of +3.6 V,RC107 Battery
Latitude D620 Battery, 312-0386 Battery, PC764 Battery, the weight ratio of energy density 70Wh/kg. To ensure that the discharge capacity can be up to 20C discharge at 0.5C discharge, Latitude D620 Battery,80%, while electricity can discharge up to 20C to ensure that the 0.5C discharge at the time of above 75%. C indicated that the discharge rate, rechargeable 1 hour discharge at 1C, charging for three hours discharge 20C.


The use of non-crystalline carbon anode, cathode to Mn (manganese)-based materials using a special element of replacement materials. Products has been developed and compared to the particles to improve the cathode structure, the use of thin electrodes, and to reduce the resistance of structural components of a great martial arts aspects. As for facing the future issues of the 2:00 session, that is the end of battery life can also be low-temperature work, as well as in maintaining the power density at the same time increase the energy density.


Tube-type solid oxide fuel cell successfully developed


A few days ago, the Chinese Academy of Sciences Dalian Huawusuo the use of low-cost preparation of inorganic membrane technology successfully prepared tube solid oxide fuel cell, single-tube 1.0V battery open circuit potential in more than 800 ℃, 0.7V the output power up to 25W above.RC107 Battery The tube-type cell research breakthrough for the development of solid oxide fuel cell distributed power plant and power station to provide a key focus on technology.


Solid oxide fuel cell membrane electrode configuration of the main plate and tube. Tube-type battery has good stability, ease of amplification module, suitable for the establishment of power stations, but the electrolyte membrane electrode electrochemical vapor deposition in general (EVD) technology to prepare, cost expensive. Therefore, the development of low-cost tube-type membrane electrode manufacturing technology, the development of solid oxide fuel cell power plant is crucial. Direction in the Chinese Academy of Sciences and Ministry of Science and Technology project, supported by cast Dalian Huawusuo in solid oxide fuel cell membrane electrode forming the base, electrolyte and cathode coating film coating technologies,RC107 Battery
Latitude D620 Battery, 312-0386 Battery, PC764 Battery, such as the preparation made significant progress, the success of the preparation  8mm × 500mm tube film electrode to solve the single-tube flow cell and sealed set of technical issues, the battery is good for repetition priming, high reliability. In the tube during the preparation of membrane electrode, the use of low-cost preparation of inorganic membrane technology, abandoning the high cost of chemical vapor deposition CVD correspondence and EVD technology, a significant reduction in the tube of Preparation of the cost of batteries for the future type of toshiba tecra a5 battery, toshiba tecra a6 battery industry technology development and solid oxide fuel cell has laid a good practical use of the technology base.

Special equipment sub-industry growth opportunity

Special equipment sub-industry growth opportunity


“Development of China’s electronic special equipment for the electronics and information industry laptop battery to provide strong support,” dell laptop battery This is the consensus of the industry. However, China’s electronic special equipment manufacturing industry is still very small scale, can not meet domestic demand.


According to statistics, in 2003 China’s electronic special equipment sales revenue was 34.2 billion yuan,YD626 Battery, 312-0393 Battery
Latitude D800 Battery, accounting for only the electronic information product manufacturing sector by 0.2%, while international electronic equipment in the electronic information industry, the proportion of about 5% ~ 10%. Domestic electronics enterprises grasp of China’s electronic information industry brought about by the rapid development of the opportunity, to extend the product line, expand equipment services, has become the focus of widespread concern.


Semiconductor Equipment extend to other areas of toshiba battery


According to market research firm statistics,Inspiron 8500 Battery, in 2003 the semiconductor equipment market in China reached 1.7 billion U.S. dollars, accounting for global market sales of 5.2%. More to industry estimates, the next 10 years, China’s semiconductor and IC equipment market will be more than 20 billion U.S. dollars. However, the rapid development of China’s semiconductor and integrated circuit industries as compared to domestic semiconductor equipment manufacturing industry is relatively slow development of the new 6-inch, 8-inch IC factories are almost all imported equipment from abroad, whether in technical or in the capital are constraining the development of China’s IC industry. To this end, the industry’s authoritative source, the semiconductor integrated circuit device companies in China should go step-by-step: by the year 2010, our part of the mainstream production line to achieve the commercialization of key equipment;YD626 Battery, 312-0393 Battery
Latitude D800 Battery, through external cooperation, will have the advantage of a small amount of the industrialization of the products; actively develop FPD , MEMS, batteries and other electronic equipment production lines based on products used in semiconductor devices. This is for the domestic semiconductor equipment business provides a broad market.


At the same time, industry experts said that by 2020, following the next-generation 45-nanometer lithography machines will be there. Latitude D800 Battery,Half of the next generation lithography technology is new, even if engaged in the original production lithography machine is the new foreign companies, therefore, when the domestic enterprises and foreign companies almost on the same starting line, the difference is not great. The 18 nanometer technology in 2018 will be launched in the domestic equipment companies do have a chance.


In addition, the semiconductor devices in a wide range of applications in other fields, as well as domestic equipment manufacturers opportunities. According to the Ministry of Information Industry Electronic Information Products Management Division Wang Bo China, the foundation of electronic products to small and micro-oriented development, semiconductor device has been increasingly applied to the LED (including semiconductor lighting), TFT-LCD, PDP, MEMS , VFD, in areas such as solar cells.


Figures show that the global LED next 5 years for 20% annual growth rate from 2004 to 3200 million U.S. dollars in 2008 increased to 5.6 billion U.S. dollars, 312-0393 Batterywhile China’s LED market grew 30%, LPE / VPE / MOCVD, and many other semiconductor devices will be useless. Although there is a nurturing process of the market, but the lighting project at the country’s support, should have good prospects.


2003 global LCD TV sales reached 35.7 billion U.S. dollars, will reach 47 billion U.S. dollars this year, the next 4 years an area of 10 inches and larger LCD panels to expand production capacity of 4 times,YD626 Battery, 312-0393 Battery
Latitude D800 Battery, the output will be 9.6 million this year to grow to 2008 3980 10,000, almost all production equipment of semiconductor devices; the global OLED market in 2003 was 263 million U.S. dollars, by 2008 will grow to 3.4 billion U.S. dollars, including equipment used in lithography, etching machines, absorbed significant equipment; MEMS industry average annual growth rate of more than 20%, in 2003 the global production value of more than 9 billion U.S. dollars,YD626 Battery, the need for lithography equipment mainly machines, etching machines, binding equipment. Domestic equipment manufacturers can develop new markets in these areas.


In addition, MOVCD, PECVD and other equipment should also be used in the battery industry well in 2003, CRE Qixing battery production equipment in short supply in this area describes the business of domestic equipment is worth to try.


SMT equipment starting from the lead-free

Fuel cell power generation compared with other unique advantages

Fuel cell power generation compared with other unique advantages.


And high efficiency.dell laptop battery Without fuel cell power generation from geothermal energy to mechanical energy again to the conversion process, there is no link in the middle of the energy loss. At present, thermal power or nuclear power is the highest efficiency of 40 percent,GD761 Battery, KD476 Battery, TD347 Battery
Inspiron 1000 Battery, while the fuel cell power generation efficiency is generally 40% ~ 60%. High melting temperature carbonate and solid electrolyte type fuel cells dell battery, emissions of heat can also be used for the second generation. The use of waste heat for heating or combined together for power generation, fuel cell utilization efficiency up to 70% ~ 80%.


Flexibility. Fuel cell power generation device is composed of a number of basic units. A basic unit is a two folder electrolyte electrode plate. The basic unit will be assembled hundreds of them would constitute a battery pack, battery pack and then together to form a power station. Can be flexible depending on the needs of different size to the assembly of fuel cell power plant. The basic unit of fuel cell design standards can carry out large-scale pre-production, so the fuel cell power plant construction and low cost, short construction cycle. In addition, as a result of fuel-cell light weight, small size, high specific power, relatively easy to move up,Inspiron 1000 Battery, so it is particularly suitable in remote areas or islands to build power stations, or build a distributed power plant.


Fuel diversity. Although the fuel cell hydrogen is mainly the work of the material, but it can be used for fuel gas, methanol, liquefied petroleum gas and other hydrocarbons. According to the actual situation, in line with local conditions to use a different fuel, or combination of different fuel use, can reach local materials, to save resources.


Pollution-free. The main product of fuel cells is water, essentially non-emission of harmful gases, it is a very clean source of energy. It is reported that a number of fuel cell emissions of harmful gases in the United States national standards for environmental protection by two orders of magnitude lower. In addition, the fuel cell is a stationary power generation, has no mechanical transmission device,GD761 Battery, KD476 Battery, TD347 Battery
Inspiron 1000 Battery, only in the control system and other auxiliary devices have moving parts, thus it is the work of a small vibration, low noise.


Due to high cost of fuel cell, generating cost-effective as other methods do not, we can not get the promotion. Therefore,TD347 Battery only the cost of significantly reduced and further enhance the service life, fuel cells will enhance their competitiveness. According to the U.S. departments of statistics, when the construction cost of 3 U.S. dollars per watt hours (1994 has reached), the fuel cell will be able to enter the market; when reduced to about 2 U.S. dollars, can be in remote areas as an independent power generating system; When reduced to about one U.S. dollars, the market will expand rapidly. 1 U.S. dollars to achieve this goal, it is necessary to the life of fuel cells will be increased to 40,000 hours.


The development of fuel cells is now very fast speed. In accordance with national plans, by 2000, Japan’s fuel cell power output will be close to 2200 megawatts, the United States will reach 500 megawatts in 2000, Europe will reach 500 ~ 900 MW. By 2010, the world’s total installed capacity of fuel cells will reach 60,000 MW. As a new type of fuel cell energy, is still relatively high cost, long life is not enough, power is still relatively small. However, with the depth of the research work, these problems will be solved. Many scientists believe that the era of knowledge economy in the 21st century, fuel cells will account for in the field of energy in a pivotal position, therefore, have the fourth-generation power technologies,KD476 Battery, research and development of fuel cells with the significance of the next century.


Dianchi Lake every year 100,000 tons of refuse what way

Dianchi Lake salvage garbage placed where it? Dianchi Lake every day along the flow of garbage to deal with the future, what will? This reporter visited the HKMA Kunming Yunnan, Kunming Environmental Protection Bureau, Kunming sanitation experts monitoring center after that, GD761 Battery, KD476 Battery, TD347 Battery
Inspiron 1000 Battery,a massive clean-up campaign refuse Dianchi Lake basin has been fully launched in the next few days, but the inflow of garbage along the Dianchi Lake how to deal with,GD761 Battery, it is worth exploring one of the new problems.


Refuse disposal sites will be built lake


Kunming, Yunnan Province, according to the HKMA person in charge, the current agricultural non-point source pollution of Dianchi Lake pollution accounts for 40 percent, and 15 lake township agricultural population of about 700,000 people, an annual output of 100,000 tons solid waste per day about 280 tons. Collected as a result of the lack of lake township removal treatment systems, the main river into the lake and piles of refuse, garbage dumping in rural areas has become the main channel, garbage and sewage directly or indirectly discharged into Dianchi Lake.

Polymer lithium-ion batteries in all related materials made

Polymer lithium-ion batteries in all related materials made


Recently, companies from the Chinese Academy of Sciences,dell laptop battery Chengdu Organic Chemistry, Chinese Academy of Sciences assumed the scale of the industrialization of technological innovation specific action items - "high-capacity polymer lithium-ion battery" items, 08k8193 battery, 08k8195 battery, Inspiron 2200 Battery, 312-0292 Battery
INSPIRON 2600 Battery, INSPIRON 2650 Battery,08k8196 battery separator materials in order to bring a breakthrough in polymer lithium-ion battery industrialization around and focus on the key materials, key technologies, key personnel and the key to the core issues, with the formation of independent intellectual property rights and the competitiveness of core technology of the battery separator materials and polymer lithium-ion battery technology and manufacturing processes, which greatly promoted the the process of industrialization.


China’s lithium-ion battery production and sales after Japan, the world’s second out, but in China, the United States, Japan and South Korea these global production and marketing of lithium-ion batteries in large countries, China is the only master the core of polymer lithium-ion batteries key technologies countries, lack of materials and battery manufacturing process has been the monopoly of foreign technologies and markets has become China’s lithium-ion battery constraints and related materials industries of the potential for sustainable development.


Since 2004, the Chengdu Organic Chemistry in the country "15 863" plan based on the results,INSPIRON 2650 Battery, through the House the scale of the industrialization of technological innovation projects in support of special operations, further improve and validate the first at home and abroad and have their own intellectual property rights of the polymer lithium new type of divide-ion battery materials and key technologies, the formation of the six million meters 2 / year production capacity of the scale of the barrier material to fill the gaps, to achieve a polymer lithium-ion battery made of all relevant materials.


In addition, Chengdu organic materials company based on the divide is different from the U.S. Bellcore has developed a patented polymer lithium-ion battery manufacturing technology.Inspiron 2200 Battery, 312-0292 Battery
INSPIRON 2600 Battery, INSPIRON 2650 Battery, The technology can be with liquid lithium-ion battery manufacturing technology and equipment linked to significantly reduce the polymer lithium-ion battery production cost, to overcome the complexity of the U.S. Bellcore technology, low yields, manufacturing costs are high and the stability of poor battery defects solved the spontaneous combustion of lithium-ion battery,INSPIRON 2600 Battery, the explosion in applications such as security issues, the formation of the company’s core technology with unique competitive technologies and processes, has applied for 10 patents in China, authorized by 2, lithium-ion 08k8197 battery, 08k8198 battery, 08k8199 battery in the domestic competition in the industry to occupy a favorable position.


In the project to promote the industrialization of the process, the company seize the talent and these two key aspects of the market. In terms of talents, one well-known from the introduction of battery management and marketing, human resources and strengthening the backbone of technology and production of training, research and development has been the formation of middle and senior management staff and 10 of 62 skilled workers and innovative sense of unity and cooperation team of professionals. Market, the company seize the domestic coal miner’s lamp battery safety of the existing lack of much-needed opportunity for replacement and successfully into the miner’s lamp battery market and is gradually driving force for the development of electric bicycle battery market and overseas market power tools battery. The next few years,312-0292 Battery the company plans to Chengdu Organic Chemistry of electric vehicles, renewable energy storage systems, aerospace and military fields, such as expanding market space.


At present,Inspiron 2200 Battery, 312-0292 Battery
INSPIRON 2600 Battery, INSPIRON 2650 Battery, Chengdu developed organic polymer lithium-ion battery has been through the national "863" electric vehicle battery testing based security testing, miner’s lamp with polymer lithium-ion battery of light through the National Quality Supervision and Test Center battery battery performance and safety detection. Chengdu is located in the industrial port dragon Shuangliu 1,000,000 / year the size of polymer lithium-ion battery production lines will be put into operation recently became the first independently developed the use of materials and divide with independent intellectual property rights of polymer lithium-ion battery technology achieve polymer lithium-ion battery industry enterprises. The industrialization of the project will become the company grow in size and strength and size of the boosters of the new industry growth.


Tsinghua University, full-vanadium redox flow battery development success


Developed by Tsinghua University, a wholly-vanadium redox flow battery (VRB),Inspiron 2200 Battery, from the principle of positive and negative cells to avoid the activities between the different types of mutual penetration of material generated by cross-contamination to meet the community’s sustained, stable, and controllable electrical energy demand.

It is reported that due to wind, solar and other clean energy changes over time the energy density of a significant change, caused by power generation devices exist significant fluctuations in power output and are difficult to meet the community’s sustained, stable, controllable electrical energy needs. The product through different valence state of vanadium ions into each other to achieve the storage and release of energy is the only power many chemical species of elements using the same 08k8201 battery, 08k8214 battery, Inspiron 2200 Battery, 312-0292 Battery
INSPIRON 2600 Battery, INSPIRON 2650 Battery,92p1011 battery system can be unstable energy input into continuous, safe and reliable output to solve large-scale use of wind energy, solar energy storage in the process of major technical problems.

This technology can also be applied to the existing grid system of ‘extinction peak load Valley’, to improve the safety and reliability of power grids and communication systems in areas such as emergency power supply will have broad application space. Experts predict that the technology development and utilization of several billion dollars a year will have a market demand.